HIROSE PAPER MFG. CO., LTD.

Employees' Blog

I Made Paper from River Branches

Published on: 2025.02.27 Last updated: 2026.04.16
thumbnail: illustration of handmade paper by the river

Why I Tried This

Before I joined Hirose Paper Manufacturing, I did something a little unusual: I tried to make paper from scratch, using branches I picked up from a riverbank.

Two reasons pushed me into it. First, genuine curiosity — I wanted to understand what paper actually is, not just read about it. Hands-on experience seemed like the fastest path to real knowledge. Second, I’ll admit, I thought it would make a strong impression in my job interviews. (More on how that went at the end.)

Gathering Branches and Scraping the Bark

I collected branches along the Yamashina River in Kyoto. Turns out riverbanks are surprisingly good places to find raw materials — I had more options than I expected.

After collecting the branches, I had to remove the bark using a craft knife. This turned out to be the hardest part of the entire process.

Older, weathered branches were forgiving — the bark practically fell off with a light scrape. Young branches, though, were a different story. They were surprisingly tough, and no matter how hard I worked the knife, the bark refused to budge easily. By the end, the skin on my hands had peeled off too.

Bleaching and Boiling

I cut the peeled branches into small pieces, packed them into a jar, and soaked them in household bleach for about a week. The bleach softens the fibers and lightens the color — or so I hoped.

After soaking, I boiled the pieces to soften them further.

Branches soaking in bleach
Branches during the bleaching process

The color didn’t lighten as much as I expected. The fibers stayed a warm, earthy brown — like water you’ve simmered burdock root in. The finished paper ended up brown too. Honestly? It gave the paper a kind of charm. I grew to like it.

Once soft enough, I ran the fibers through a home blender to break them down further.

Bleached branches after running through the blender
Bleached branches after running through the blender

Preparing for Papermaking

Traditional papermaking requires a suketa — a flat mesh frame used to scoop and drain the fiber slurry. I built mine from a 100-yen wooden photo frame and a piece of lace curtain as the mesh. Simple, but it worked.

I also needed neri, a viscous liquid that helps the fibers distribute evenly during the forming process. It’s traditionally made from tororo-aoi (a plant in the mallow family), but I discovered that okra works as a substitute. I soaked okra in water until it turned slippery and used that instead.

Okra soaking in water as a neri substitute
Okra soaking in water — my stand-in for neri

For learning the fundamentals, improvised tools are perfectly fine. I wouldn’t recommend them for serious production — but for understanding how papermaking works, they do the job.

Time to Make Paper!

The actual papermaking was a lot of trial and error.

Getting the fiber distribution even was harder than I thought. Scooping with the right amount of force — enough to spread the fibers, not so much that they clumped — took several attempts to get a feel for.

Forming a paper sheet with the handmade suketa frame
Forming a sheet — getting the force right took several tries

Transferring the newly formed sheet from the mesh frame to cloth was equally delicate. Too heavy a hand and the whole fragile sheet would break apart.

After forming, I pressed each sheet between newspaper layers and weighted it down with a heavy book to squeeze out the moisture. Then I let it dry for a few days.

Freshly pressed paper before drying
After pressing, just before drying

The finished paper was honestly a bit rough — slightly crumbly, brownish, and not something you’d write a letter on. But I had made it with my own hands, from branches I picked up off the ground. That felt genuinely good.

The finished handmade paper
The finished paper (more or less)

Closing Thoughts

After I joined Hirose Paper Manufacturing and walked through the factory floor, something clicked. The industrial papermaking process suddenly made sense in a way it never had before.

The machines are enormous. The scale is completely different. But the core logic is the same: dissolve fibers in water, spread them into a sheet, drain the water, dry. The same sequence I stumbled through in my kitchen.

There’s a Japanese saying: hyakubun wa ikken ni shikazu — “hearing something a hundred times is not as good as seeing it once.” I’d go further: doing it once is better still.

If you’re curious about how paper is made, I’d encourage you to try it. You don’t need special equipment. A photo frame, some okra, and a handful of branches from a riverbank will get you started.

Oh — and that strategic plan to impress my interviewers with this story? I completely forgot to bring it up during my final interview. Half a year later, it finally gets its moment here. Better late than never, I suppose.

Pixcel Art of Aki. holdin a cat.

About the Author

Aki Matsumura

Joined HIROSE PAPER MFG. CO., LTD. in November 2024.

Brings a diverse professional background spanning retail, welfare services, and food service before transitioning into system development.

Currently serves as an in-house systems engineer, responsible for internal database development and system improvement initiatives across the company.

View posts by this author